Dana 35 gear oil capacity.

Jun 28, 2009. #1. My 2000 Ford F-350 DRW came with a 4.10:1 geared dana 80 dualie axle. IT was factory filled with 75W-90 But ford has since updated to use 75W-145 for in service fluid changes on the rear ends. The other manufactures that use the Dana 80 (mainly mopar) still spec the 75W-90 in their rear ends.

Dana 35 gear oil capacity. Things To Know About Dana 35 gear oil capacity.

The fluid looked good, as did the gearing and locker.) I replaced the chrome cover that was previously installed with a Rugged Ridge cover. From what I have found, the Dana 44 should take 3.6 pints of gear oil. Does that sound about right for what is supposed to be a 1971 Dana 44?Dana 30 - 1.25 quarts 75W-140 Dana 35 - 1.75 quarts 75W-140 * Dana 44 - 2 quarts 75W-140 * Rubicon Dana 44 (FRONT) - 1.375 quarts 75W-140 synthetic Rubicon Dana 44 (REAR) - 2 quarts 75W-140 synthetic ** * 4 oz of friction modifier is required with Trac-Lok limited slip differential. The extended drain program and any extended warranty program are separate programs. Note: For specifi c detail on Dana extended warranty programs refer to the Dana Warranty Guide or call 1-877-777-5360. Note: For a complete list of Dana “approved lubricants” for extended drain, refer to Approved Lubricant Suppliers Manual, DALSM072012. Mar 22, 2009 · Received 475 Likes on 422 Posts. NCM Sinkhole Donor. For gear oil, you can use a good grade of GL-5 rated 80W-90 (Valvoline is fine) and a bottle of the GM posi additive. Shouldn't take more than 2 quarts. For the driven gear, go to a reputable tranny shop or try the dealer. Just tell them you have 3.45 gears and you need the gear for a 700R4 ...

Dana Australia Dana Spicer Parts Quick Reference Guide • 3. 5. Axle Shafts. Axle Shafts are identified by the part number on the edge of flange or by using the dimensions as shown in the diagram below. Part No. Body Spline Flange Bolt. Length Diameter O.D. O.D. Circle No. Hole (in) (in) (in) (in) (in) Holes Type. START.

It had auto trans fluid in it. I didn't think it was unusual because the suburban runs with that. What I learned from all the helpful folks is the D 300 is a gear driven design and uses gear oil (85w90).Suburban is chain driven and uses dextron. I just use the 80w90 from walmart. (Checking every other week cause it leaks out)

3. Location. Kingwood, Texas, USA. Nov 21, 2019. #1. Good Morning folks-. I am looking at changing the lube in my "Fat Boy" 08' F-450 that just hit it's 50K mark. The Rear Differential is a Dana 110. Ford calls for a lube change at this time with 75W-140, and i wondered if there as any reason not to go with the Valvoline Synpower, as opposed to ...The extended drain program and any extended warranty program are separate programs. Note: For specifi c detail on Dana extended warranty programs refer to the Dana Warranty Guide or call 1-877-777-5360. Note: For a complete list of Dana “approved lubricants” for extended drain, refer to Approved Lubricant Suppliers Manual, DALSM072012.dana 44 rear diff fluid amount. diff fluid differential fluid level. Jump to Latest Follow. 27K views 29 replies 6 participants last post by DoubleOught Mar 25, 2014. dirtbag90 Discussion starter. 96 posts · Joined 2014. #1 · Mar 21, 2014. My rear dana 44 was only able to take about 1 and 3/4 qt. I know manual says 2 qts or 4 pints.5651 posts · Joined 2009. #1 · Sep 23, 2016. I changed the fluid a few days ago. The owner's manual states "10.1" pints capacity which includes the 10 ounces of friction modifier. This is also the capacity posted in the Geno's Garage tech section. The owner's manual also states to only fill to a level "3/4 inch below" fill plug hole.

Jun 17, 2023 · The dana 60 fluid capacity varies depending on the specific application. However, most dana 60 axles require approximately 2. 5 quarts of gear oil. The dana 60 axle is a heavy-duty axle commonly used in trucks, suvs, and off-road vehicles. It’s known for its strength and durability, making it a popular choice for those who need to tow heavy ...

When it comes to maintaining your motorcycle’s performance and ensuring a smooth ride, checking the fork oil capacity is an essential task. The fork oil not only lubricates the sus...

Location. Chicago, IL. Feb 6, 2014. #10. Agree with Zaedock, regular 'ol 80w-90 works great in these. If you want to get fancy you can spring for a synthetic 75w-90 …Carrying capacity is the idea that sustainability requires balance. Learn about carrying capacity and human population. Advertisement ­­In 1798, an English clergyman named Thomas M...It’s about twice as expensive as conventional 80W-90, and maybe 30% more than conventional 85W-140 gear oil. Still, the absolute cost difference is typically less than $20. For $20, it’s kind of a no-brainer. How Much Gear Oil Does A 14 Bolt Axle Need? The gear oil capacity of a 14 bolt axle is either 3.6 quarts (full float) or 2.75 quarts ...I checked the Dana website and the info they have is to use a minimum of S.A. E. 80W/90 multi purpose gear lube. They recommend to use the specified lubricant that the vehicle manufacturer recommends. Thanks in advance. Don. 2003 7.3 PSD 2wd XLT super cab long box, drw, automatic trans. 410 gears, stock exhaust with muffler delete, PHP chip ...specs the Ford corporate (Sterling) 10.5" rear ends with 75W-140. synthetic lube in 2002. So that part appears not to have changed from 1999.5 to 2002. But more recently there was a discussion on this forum about Ford changing. the lube spec for 2002 (and up I believe) F-350 duallies with the Dana-80.4.3v6,t18,dana18, ford/chevy driveshaft, chevy front in front, chevy front in rear

Jul 27, 2010 · mrmoparwl. 339 posts · Joined 2009. #9 · Aug 3, 2010. The problem with only one bottle is the increased amount of fluid the Dana 70 and 80s have over the 60. Seen enough of the 70s eat up the clutches by not adding enough slip lube. When I service any 70 or 80 min amount is 1 1/2 bottles in the 70 and 2 in the 80. The Dana 60 spec is just under 3 quarts. In my personal experience, the Dana 50 will take about 2.5 - 2.75 quarts to fill to the plug. As far as I know, the D50 and D60 use the same case, so they SHOULD have the same capacity. Be warned though, if your inner axle seals are bad, overfilling will make that obvious.Gear Oil Capacity for AEV Diff Covers? 01-06-2020, 07:14 PM. Jeep JK Rubicon front Dana 44 2.70 pints (1.35 quarts) Jeep JK Rubicon rear Dana 44 4.75 pints (2.375 quarts) AEV bottom (front) fill hole: under 1 quart? AEV top (rear) fill hole: 1.75 quarts.Conclusion. The amount of gear oil you need to fill a Dana 44 axle depends on the type of axle you have and the type of oil you choose to use. Generally, you should use 3.5 quarts of gear oil for a Dana 44 axle with a standard differential. If you are using a synthetic gear oil, you should use 4 quarts instead.17,625. Location. taxifornia,soon 2b Arizona. I had a good friend (passed away now from cancer) who made his living as a one man rearend shop. His specialty was nine inch ford for racers, but he could work on anything. If the customer insisted on synthetic gear oil, he would warrantee his work for six seconds/six inches, whichever came first.

50629 posts · Joined 2005. #3 · May 7, 2015 (Edited) Nearly any major brand GL-5 gear lube is fine. Valvoline, Castrol, Torco, Havoline, etc. will be good. A 75W-90 is good around town, a heavier viscosity like 80W-120 or 85W-140 is good if you tow a trailer or wheel extreme trails. Ever since custom axle builders like Currie discovered ring ...Its really not a huge deal. lots of people have run gear oil lots have run the standard 50W SAE engine oil that ford recommened. Basically run what you like. ... Yukon Dana 44 oil capacity more than 2Qt? keymonkey; Mar 13, 2023; Bronco Tech; Replies 5 Views 740. Mar 14, 2023. keymonkey. Y. Dana 20 Oil Observation - Noise. Yooper74; …

Models with Dana 44 axle: 80W-90 GL-5 gear oil; ... Dana 35: Commonly used in the rear axle of older Jeep Wranglers. While sturdy, it’s not as robust as the Dana 44 and may be a weak point for heavily modified vehicles. ... Typically, the front differential capacity is around 1-2 quarts, while the rear differential takes 1.4-1.5 quarts 3,8 ...XFE 75W-85: Available in 5-gallon containers. Spicer XFE 75W-85 synthetic gear lubricant is our most fuel-efficient lube to date. You can enjoy a 1.9% fuel savings improvement over standard FE 75W-90 oil and extend the warranty on your Spicer heavy-duty or medium-duty carriers. Improved fuel efficiency. Extended drain interval: up to 500,000 miles.When you remove the filler plug, the oil should start to run out. If it does not, replenish the supply until it does". That's fine for a stock axle in that has not been modified. Swap in a CV driveshaft and you point the yoke up, which lowers the level of the fill hole. Suddenly you can't put as much gear lube is as before, which is not good. Capacity: Dana M190: 2019-2020: Motorcraft SAE 80W-90 Premium Rear Axle Lubricant: 1.64-pints (0.775 Liters) Dana 35 SLA: 2001-1998: Motorcraft SAE 80W-90 Premium Rear Axle Lubricant: Front axle L (pint) 1.54 (3.25) / Lubricant level mm (in) 9.56 (0.38) below bottom of axle cover filler hole: Dana 35 TTB: 1990-1997: Hypoid Gear Lubicant SAE 80W ... This towing capacity chart shows vehicles' towing capacity by make and model. Find your towing capacity on HowStuffWorks' towing capacity chart. Advertisement Towing capacity, some...Dana 35 Oil Capacity; Extra Capacity BRAND; G2 Axle and Gear (2) Alloy USA (1) RT Off-Road (1) Rugged Ridge (1) Type Of Material; Aluminum (4) Steel (1) Finish Type; Natural (1) Powder Coated (4) Popular Axle Manufacture; ... they are designed to help cool your gear oil for prolonged bearing life. Made from high strength heat treated aluminum ...If it's a '75, it will be a 9 1/4", it will have the 5 on 4.5" bolt pattern, as will the '77 model axle and any other 1/2 ton axle built between '75 and '79. In '80 they went back to the larger 5 on 5.5" bolt pattern. You can swap parts but if you swap the entire axle you will end up with mismatched wheel patterns.how much gear oil for dana 60? Thread starter 73dodge; Start date Sep 24, 2007 - 7. 73dodge Well-Known Member. Joined Sep 12, 2007 Messages 65 Reaction score 0. Sep ...Definitely NOT a 10.5L Sterling, which makes the literature wrong. Looks like you need 4.0L of 75w-90 synthetic oil. Depending on brand you may need to add ~8 oz of friction modifier, Ford calls theirs XL-3. Some synthetic oils come with friction modifier, so you may not need it.

Can't seem to find an exact spec . It is the Dana 70 with Limited slip my truck is in my sig. Thanx in advance for the help. 2002 2500 QC LB, 4x4, SLT Laramie. S&B CAI Silencer Ring MIA, Fass 150, AFE Bladerunner Intake Horn, MBRP 4" TB Exhaust Quadzilla Boost Fooler, BD APPS noise isolator, FOX 2.0 shocks and 34x12.50 Hankook DynaPro MT.

The extended drain program and any extended warranty program are separate programs. Note: For specifi c detail on Dana extended warranty programs refer to the Dana Warranty Guide or call 1-877-777-5360. Note: For a complete list of Dana “approved lubricants” for extended drain, refer to Approved Lubricant Suppliers Manual, DALSM072012.

Jan 4, 2009 · Points. 18. Location. Forest, VA. Jan 4, 2009. #1. according to advance auto, the IH dana 44 is supposed to take 1 1/2 quarts of gear oil. This is the first time I've changed out the gear oil in a scout and I was only able to get 1 quart in before the oil started leaking back out. Is this correct? Definitely NOT a 10.5L Sterling, which makes the literature wrong. Looks like you need 4.0L of 75w-90 synthetic oil. Depending on brand you may need to add ~8 oz of friction modifier, Ford calls theirs XL-3. Some synthetic oils come with friction modifier, so you may not need it.365. Jan 14, 2011. #10. Believe owner's manual specifies, 50 weight engine oil. Has been a tad bit of improvements in gear box oils since 1966. Suggested reading is, ANSI/AGMA 9005-E02. As the Dana 20 has neither bronze synco rings, or friction surfaces, oils with extreme pressure additives will prove beneficial.*Rear Differential Oil Capacity-Dana 80 (Conventional/ Truetrac diff) 8.5 pt-Dana 80 (Trac Loc) 8.0 pt-Dana S135 24.5 pt-Ford 10.50-Inch Ring Gear 7.0 pt-Friction Modifer 8.0 oz *Rear Differential Fluid Type *Ford 10.50 Inch Ring Gear -SAE 75W140 High Proformance Rear Axle Lubricant-Additive Friction Modifier C8AZ-19B546-A *Dana 80 AxleWhen it comes to maintaining your motorcycle’s performance, one crucial aspect to consider is the fork oil capacity. The fork oil plays a vital role in ensuring smooth suspension o...Dana 35 - 1.75 quarts 80W-90 or 75W-140 *. *4 oz of friction modifier is required with Trac-Lok limited slip differential. …It had auto trans fluid in it. I didn't think it was unusual because the suburban runs with that. What I learned from all the helpful folks is the D 300 is a gear driven design and uses gear oil (85w90).Suburban is chain driven and uses dextron. I just use the 80w90 from walmart. (Checking every other week cause it leaks out)spillz Discussion starter. 160 posts · Joined 2007. #11 · Jan 3, 2014. Called ARB. Hi everyone, I called ARB tech department with my concerns as to the correct amount of fluid for my differentials. ARB Tech. stated that they would require the factory amount in each diff, which is 2.5 pints in Dana 30 and 4.0 pints for the Dana 44.Synthetic 80/90: Jeep JK Rubicon front Dana 44 2.70 pints (1.35 quarts) Jeep JK Rubicon rear Dana 44 4.75 pints (2.375 quarts) Non Rubicon front differential 2.10 pints (1.05 quarts) Non Rubicon rear differential 3.80 pints (1.90 quarts) As for your Rubicon, yes, you need the additive. Most Saharas do also. Motorcraft SAE 5W-20 Super Premium Motor Oil or Motorcraft SAE 5W-20 Synthetic Motor Oil (Canada) CXO-5W20-LSP12 or CXO-5W20-LFS12 (Canada) / WSS-M2C945-A Engine oil (Diesel engines) Refer to the diesel supplement. Fuel tank (incomplete vehicle, steel tank, middle location)

Aug 21, 2013 · 336 posts · Joined 2012. #6 · Aug 21, 2013. Mines a 98 5 speed with dana 80 in the rear 60 in the front. If I remember correctly I used just over 4 quarts of royal purple 75w-90. Get some rtv gasket maker put a good bead around the plate and put it on, let the gasket sealer set for a few mins before fully tightening. Superior Axle & Gear offers its Super 35 kit and Warn has a full-float kit. The Super 35 kit is available for both C-clip and non-C-clip axles. The kit replaces the …Parts:Dana 35 Differential Plug: http://amzn.to/2wU5zcnRTV Gasket Maker: http://amzn.to/2wU1YuFGear Oil 75W-90 GL5: http://amzn.to/2wjjGGsBrake Cleaner: http...Instagram:https://instagram. 4100 main st riversidecheap 3 bedroom houses for rent in nashville tnwhere is christel bell on fox 4 newslayton simon brother The ring gear diameter is 10.5" The 35 spline versions are the same spline as the 35 spline 60’s and 9 inches we are all used to ... smokin: The oil capacity is about 3 quarts, Dana recommends 80w90 gear oil The housing is ductile iron (a high quality type of cast iron) The input torque rating is 7000 lb/ft max, 1750 lb/ft continuous for most ...*Rear Differential Oil Capacity-Dana 80 (Conventional/ Truetrac diff) 8.5 pt-Dana 80 (Trac Loc) 8.0 pt-Dana S135 24.5 pt-Ford 10.50-Inch Ring Gear 7.0 pt-Friction Modifer 8.0 oz *Rear Differential Fluid Type *Ford 10.50 Inch Ring Gear -SAE 75W140 High Proformance Rear Axle Lubricant-Additive Friction Modifier C8AZ-19B546-A *Dana 80 Axle driver license office clayton reviewslux theater in caldwell Always fill to the proper level regardless of capacity listed. I really can't help with questions about the M200, other than its a Dana 35. Knowing what I know about lubricants for industrial gear drives, I can only assume that the M200 sees higher loads than the M220, requiring a lubricant with a higher viscosity at operating temperature. patientfirst com my account TJ diff fluid. I am wanting to change the fluid in the front and rear diffs and I am not sure of the capacity or which axle I have. The front is stamped with DANA 40869-136-0 and the rear is DANA 43225-115-0. I am thinking the front is a Dana 35 and the rear is a Dana 44 but I might be wrong. It is a 2001 Sahara. Capacity: Dana M190: 2019-2020: Motorcraft SAE 80W-90 Premium Rear Axle Lubricant: 1.64-pints (0.775 Liters) Dana 35 SLA: 2001-1998: Motorcraft SAE 80W-90 Premium Rear Axle Lubricant: Front axle L (pint) 1.54 (3.25) / Lubricant level mm (in) 9.56 (0.38) below bottom of axle cover filler hole: Dana 35 TTB: 1990-1997: Hypoid Gear Lubicant SAE 80W ...